Installation Instructions for Alpine

904-ALP-W-RD-H1-05

Install the Fixture

ALP-W-RD-H1-_

1718 W. Fullerton Ave

Chicago, IL 60614

Tel: 773-770-1195

Fax: 773-935-5613

www.edgelighting.com

[email protected]

SAVE THESE INSTRUCTIONS!

- This product is ETL listed for indoor and outdoor locations.

- RISK OF FIRE:

- This product is for wall mount applications only.

- This product can mount to either a 4" square electrical box

with round plaster ring or an octagon electrical box.

- This product can be dimmed with a standard incandescent

dimmer.

- This instruction shows a typical installation for indoor and

outdoor.

This product must be installed 4 ft above

the ground for wet locations.

IMPORTANT INFORMATION

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, electrical shock, exposure to

excessive UV radiation, or injury to persons:

- Do not look directly at the lamp while the fixture is on.

- RISK OF FIRE: Use only the type of lamp and maximum

wattage indicated in this instruction manual.

- Never cover the halogen lamp with anything other than a

lamp shield provided by Edge Lighting and never place

flammable material close to the fixture.

- Never turn the fixture on and off by connecting and

disconnecting the halogen lamp.

- Do not touch the fixture head, shade or lamp shield while

the fixture is on. These surfaces may be VERY HOT.

- Do not touch lamp at anytime. Use a soft cloth instead as oil

from skin may damage lamp.

- It is normal for a new halogen lamp to produce minor

smoke when first turned on.

- Turn power off and allow to cool before replacing lamp.

FIXTURE BODY

CANOPY

1: Remove

the fixture body and carefully pull the canopy off of the

fixture body.

the two Phillips screws and the silicon washers on

PHILLIPS SCREW

#8-32 SCREW

CROSSBAR ASSEMBLY

CENTER HOLE

ELECTRICAL BOX HOLE

2: Make sure the crossbar assembly is grounded in accordance

with local electrical codes.

3: Feed the power wires through the crossbar assembly

center hole.

4: Mount the crossbar assembly to the electrical box holes with

the provided #8-32 screws.

SILICON WASHER

1 2

Sommario

Pagina 1 - Install the Fixture

Installation Instructions for Alpine904-ALP-W-RD-H1-05Install the Fixture1ALP-W-RD-H1-_1718 W. Fullerton AveChicago, IL 60614Tel: 773-770-1195Fax: 773

Pagina 2 - Replace the Lamps

DEPHILLIPS SCREW 92FIXTURE BODY 9: Place all wires and wire nut connections inside the fixture body. Slide the fixture body completely onto th

Commenti su questo manuale

Nessun commento

Ambit Cable Modem Router U10C012 manuels

Manuels d'utilisation et guides de l'utilisateur pour Routeurs Ambit Cable Modem Router U10C012.
Nous fournissons des manuels en pdf 1 Ambit Cable Modem Router U10C012 à télécharger gratuitement par type de document : Manuel de l'utilisateur

Edge-lighting Alpine Manuale Utente

Navigare online o scaricare Manuale Utente per Illuminazione Edge-lighting Alpine. Edge Lighting Alpine User Manual Manuale Utente

Sommario

Commenti su questo manuale

Ambit Cable Modem Router U10C012 manuels

Ambit Cable Modem Router U10C012 Manuel de l'utilisateur (55 pages)

Table des matières

Plus de produits et de manuels pour Routeurs Ambit

Edge-lighting Alpine Manuale Utente

Navigare online o scaricare Manuale Utente per Illuminazione Edge-lighting Alpine. Edge Lighting Alpine User Manual Manuale Utente

Sommario

Commenti su questo manuale

Prodotti e manuali riguardandi Illuminazione Edge-lighting Alpine

Ambit Cable Modem Router U10C012 manuels

Ambit Cable Modem Router U10C012 Manuel de l'utilisateur (55 pages)

Table des matières

Plus de produits et de manuels pour Routeurs Ambit